If outer rotor thickness measures 9. Refer to proce- dure in this section. Replace the lower control arm. Refer to Seats in the Body section of this manual for the required procedure to be used for this vehicle. The batteries are avail- again.
Excessive friction in power 10. The bolt attaching the left rear lateral link must be installed with the bolt pointing forward to prevent damage to the fuel filler tube. A defective A pressure transducer on the air conditioning com- pump will not be able to circulate heated coolant pressor discharge line sends a signal to the Power-. Install nuts on attaching bolts. The six throw, nine counterweight crank- shaft is supported by four select fit main bearings with the number three serving as the thrust washer location Fig.
High or low oil level in crankcase. For infor- alignment rack so that the tires are supporting the mation and service procedures on the speed propor- total weight of the vehicle. Clean plugs and set gap. Chrysler permanently attaches the label in the engine compartment. Refer to the Fuel Pressure Release Procedure in this section. Measure the cylinder bore at three levels in direc- tions A and B Fig.
Refer to procedure in this necting rods must be removed from top of cyl- section. Install a flat blade pry tool bolts are serrated where they go through strut to keep hub from turning. When electric current is sup- plied to the injector, the armature and needle move a short distance against a spring, allowing fuel to flow out the orifice. Inflate all tires to recommended pressure 2. The lock seam main cap Tighten bolts finger tight.
Grasp inner tripod joint in one hand and intercon- Grasp steering knuckle with other hand and rotate it necting shaft in the other. Apply light pressure to assemble socket to ball. Band Torca Clamp — Catalytic Converter Pipe to — Support Bracket—Nut V-Band Clamp—Exhaust — Manifold to Catalytic Converter Exhaust Support to Body — Bracket—Fasteners Exhaust Support Bracket to — Transmission—Fasteners. Blown fuse for fog lamps. The shift cable must be fully inserted onto the pin of the shifter mechanism. Check booster vacuum hose and vacuum assist.
See Group 22, Wheels And Tires for the required balancing pro- Driveshaft assemblies are designed to transmit cedure. Disengage the lamp retain- ing tabs Fig. The module cannot be repaired, and if faulty or dam- aged will have to be replaced. Tighten the strut assembly clevis to steering knuckle attaching bolt nuts to a torque of 203 N·m 150 ft. Allow the stabilizer bar to hang down. See Hoisting in the Lubrication and Maintenance group of this service manual for the required hoisting or jacking procedure to be used for this vehicle.
Follow the manufacture recommendation for application and repair procedures. Then, install the shift cable on the shifter mechanism Fig. Dirty or incorrectly gapped plugs. Check rocker arms for wear or damage Fig. Tighten to a torque of 17 N·m 145 in.
Change oil to correct viscosity. Replace springs that do not meet specifications. See Hoisting in the Lubri- cation and Maintenance section of this manual for the required lifting procedure to be used for this vehicle. Only remove enough insulation to solder in the new diode. See Removing Guide Pin Bushings in the cali- per disassembly section of this manual.
When readjusting, do not exceed the total toe difference in width between the centered leading and specification. Oil Pan —M6 Bolts — 105 —M8 Bolts — 250 Oil Pan Drain Plug — Oil Filter — Oil Pump to Block—Bolts — 250 Crankshaft Damper Remover Insert C-4685-C2 Oil Pump Cover—Bolts —. Position wire harness routing bracket onto tubing to the rear proportioning valve. Remove knurled nut from small end of removal tool. Oil Ring Steel Rings 0. Install Pressure Hose, may be easier to access the power steering pump Special Tool 6905 in 6893 kit , in the inlet fitting on pressure fitting from the bottom of the vehicle Power Steering Analyzer.
High resistance in headlamp 2. Battery life is about two years Fig. Clean system and replace fuel filter. Mopar Gasket Maker is an anaerobic type gasket material. The switch is not adjustable. The generous collection of common equipment contains an energy moonroof, grip management, natural leather seats and warmed energy wall mirrors.