One of the three tumbling vanes will be plastic. A thermal cut-off is mounted on the clothes dryer heater box. This fuse will blow when too high a temperature is sensed at the outlet; usually when one of the operating thermostats has failed. If your dryer won't start. Washer and dryer repair Some of the most common washer and dryer problems include the washing machine not spinning, the washing machine leaking or the dryer not heating.
Our skilled technicians can repair the major kitchen appliance brands. Hold the dryer drum in place and lift the front of the cabinet off. Shopping online in the U. Turn the drum until the plastic vane is on top. You can test the elements for continuity without removing the heater. Another fairly common problem is that the dryer door support cables break.
The heater elements are located inside the riser on the right, as you look at the back of the machine. If you have a model with a kickplate, remove the kickplate, too. When the drum is in place, make sure the belt is flat on the drum and closely line up the belt on on the old belt skid mark on the drum. It takes a little acrobatics, but it isn't too tough. See chapter 2, section 2-3 a to replace.
See figure W-4 The one on the left tends to be worn more than the other one, but replace them both. The blower wheel is under the bottom of the lint screen duct to your left, as you look at the back of the dryer. Sears Home Services is the leading appliance repair service in the nation. If your dryer won't heat. Also check that the rear drum seal is flat all the way around, and not pinched between the drum and the rear support plate.
The easiest way is to push the belt tensioner to loosen the belt with your thumb, and use the fingers of the same hand to slip the loop of belt off the motor pinion. This will prevent your accidentally dropping the screws down the lint screen slot. Sears International Online Shopping If you are planning to visit the United States, or have friends and family here, shop at Sears to get everything you want—including gifts for yourself or others. Once you place an order, you or someone you know can pick it up at a Sears store, have it shipped to over 100 countries—whatever is most convenient for you. If the unit is not level, it can rock during cycles and cause noise. Remove the two top screws inside the cabinet that hold on the cabinet front.
It is a back-up for the hi-limit stat. See figure W-3 for a cross section of the cable mechanism. If the hose has any 90-degree turns, it should be no longer than 20-feet because the turn can restrict airflow and increase drying time. Before you put the cabinet front on, reach beneath the drum and make sure the two rollers are in the groove of the drum. Remove the cabinet front carefully!. No one knows Kenmore better than we do. We either have it in stock in our warehouse or we can get it from the manufacturer right away.
If this happens, see section 3-5 for access to the blower wheel. When the bias heater is energized, it generates a small amount of heat, which causes the operating thermostat to open sooner, keeping the dryer drum cooler inside. Rely on Sears Home Services for that restore comfort and safety to your home. As you turn it, check that the belt is flat all the way around. The drive belt comes directly off the front of the motor and goes completely around the drum. You can count on us for fast, efficient repairs whenever you have any of the following needs: Something like a refrigerator not cooling properly can be a major inconvenience, so you need the right fix fast. If it is badly worn, replace it.
To access the cables, lift the top of the cabinet and remove the kickplate. For electric, test the heater element for continuity. Sears Home Services is the only nationally authorized appliance repair service for Kenmore products. We are the household appliance repair provider you can trust for any problem. See figure W-5 Loosen but don't remove the bottom screws holding the front of the cabinet on. Our Free Kenmore Clothes Dryer Repair Manual was designed to assist the novice technician in the repair of home domestic dryers that have been operating successfully for an extended period of months or years and have only recently stopped operating properly, with no major change in installation parameters or location.
Sears Kenmore Gas Valve Solenoid Coil Kit - Includes both 2 and 3 wire coil in kit - As ignitor glows hot, electrical signal sent to coils to allow gas to pass through the valve. To replace the rollers, remove the drum as described in section 3-3. If you have a kickplate model, remove the belt from the motor pinion. If you have a kickplate machine, you can install the cabinet front at this time. Push the tensioner with your thumb and slip the belt loop around the motor pinion. Look inside the dryer drum.